濟南誠耐

濟南誠耐金屬製品有限公司

精湛的技術力量•╃、完善的設計服務團隊╃•₪▩☁,真誠為您提供專業的服務

全國諮詢熱線
15990909037
當前位置·•◕◕◕:首頁 »資訊中心 » 行業動態 » 安裝電梯門套時需要注意的地方有哪些╃·╃✘?

安裝電梯門套時需要注意的地方有哪些╃·╃✘?

來源·•◕◕◕:http://www.petersontaxinc.com/ 瀏覽·•◕◕◕:發表時間·•◕◕◕:2022-05-20
電梯在現代生活中是為大家提供了很大的便利╃•₪▩☁,目前6層以上的建築一般都裝有電梯•◕│✘·。而我們在乘坐電梯的時候會注意到電梯門的不鏽鋼門套╃•₪▩☁,它是用來保護電梯不受腐蝕•╃、破損•╃、髒汙等的侵襲•◕│✘·。在安裝不鏽鋼電梯門套的時候有一些需要注意的地方╃•₪▩☁,小編來給大家分享一下•◕│✘·。
Elevators provide great convenience for everyone in modern life. At present, buildings with more than 6 floors are generally equipped with elevators. When taking the elevator, we will notice the stainless steel door pocket of the elevator door, which is used to protect the elevator from corrosion, damage, dirt and so on. When installing the stainless steel elevator door pocket, there are some points that need to be paid attention to. Xiaobian will share them with you.
a·•◕◕◕:不鏽鋼電梯門套安裝注意事項如下·•◕◕◕:
a: Precautions for installation of stainless steel elevator door pocket are as follows:
1•╃、材料厚度需不低於1.2厚(實際厚度不得小於1.08)•◕│✘·。
1. The material thickness shall not be less than 1.2 thick (the actual thickness shall not be less than 1.08).
2•╃、需注意用豎料來收口門頭橫料•◕│✘·。
2. Pay attention to use vertical materials to close the door head and horizontal materials.
3•╃、注意製作基層一定要小於門套包邊尺寸5mm左右╃•₪▩☁,有足夠的空間安裝和打膠•◕│✘·。
3. Note that the base course must be about 5mm smaller than the edge wrapping size of the door pocket, and there is enough space for installation and gluing.
4•╃、門頭板寬度要略小於豎料寬度1-2毫米╃•₪▩☁,收口才美觀•◕│✘·。
4. The width of the door head plate should be slightly less than the width of the vertical material by 1-2mm, and the closing is beautiful.
5•╃、一般門頭板和立面包板對接處的陰角處不建議用膠水收口╃•₪▩☁,這樣既美觀又能檢驗門套安裝質量•◕│✘·。
5. Generally, it is not recommended to close the internal corner of the butt joint between the door head plate and the facade cladding plate with glue, which is not only beautiful, but also can check the installation quality of the door pocket.
不鏽鋼電梯門套
Stainless steel elevator door pocket
b·•◕◕◕:普通的45°拼接門套做法╃•₪▩☁,常規注意事項如下·•◕◕◕:
b: For the common 45 ° splicing door pocket, the general precautions are as follows:
1•╃、材料厚度需..1.2厚(實際厚度不得小於1.08)•◕│✘·。注意對角處不能有錯位╃•₪▩☁,旱接點一定要處理在隱蔽位置•◕│✘·。
1. The material thickness needs to be 1.2 thick (the actual thickness shall not be less than 1.08). Note that there shall be no dislocation at the diagonal, and the dry contact must be handled in a concealed position.
2•╃、注意製作基層一定要小於門套包邊尺寸5mm左右╃•₪▩☁,有足夠的空間安裝和打膠•◕│✘·。
2. Note that the base course must be about 5mm smaller than the edge wrapping size of the door pocket, and there is enough space for installation and gluing.
3•╃、一般門頭板和立面包板對接處的陰角處不建議用膠水收口╃•₪▩☁,這樣既美觀又能檢驗門套安裝質量•◕│✘·。安裝質量粗劣╃•₪▩☁,陰角打膠遮蓋瑕疵╃•₪▩☁,不建議使用•◕│✘·。
3. Generally, it is not recommended to close the internal corner of the butt joint between the door head plate and the facade cladding plate with glue, which is not only beautiful, but also can check the installation quality of the door pocket. The installation quality is poor, and the internal corners are glued to cover the defects. It is not recommended to use.
本文的精彩內容由不鏽鋼電梯門套提供知識提供╃•₪▩☁,本網站還有很多的精彩內容╃•₪▩☁,更多的內容您可以點選進入·•◕◕◕:http://www.petersontaxinc.com我們有專門的客服為您解答問題
The wonderful content of this article is provided by the stainless steel elevator door pocket. There are many wonderful contents on this website. You can click to enter more contents: http://www.petersontaxinc.com We have special customer service to answer your questions
下一篇·•◕◕◕:電梯大門套與小門套的區別上一篇·•◕◕◕:最後一頁
女闺蜜露出奶头让我吃奶,天堂最新版www,40岁成熟女人牲交片20分钟,国产精品国产三级国产专播